Mauerlat attach to the brick wall

Here at "All about the Roof," welcome! We’re going to be discussing the important subject of mounting a mauerlat on a brick wall today. A mauerlat is a horizontal timber that rests atop a masonry wall to support the roof structure. It is also referred to as a wall plate or sill plate. Every roof needs to be properly fastened to a brick wall in order for it to be stable and long-lasting.

The process of attaching a mauerlat to a brick wall requires exact planning and execution. Making sure the brick wall is structurally sound and able to support the weight of the roof is the first step. This can entail evaluating the wall’s condition and putting in any reinforcements or repairs that are required.

Next, it’s critical to choose the appropriate supplies and fasteners for the task. To fasten the mauerlat to the brick wall, corrosion-resistant screws or bolts are usually utilized. These fasteners ought to be long enough to provide a strong anchor point for the wood and to pierce deeply into the wall’s structure.

It’s also crucial that the fasteners are spaced appropriately along the mauerlat. By doing this, the roof load is distributed evenly and concentrated stress points that might eventually erode the connection are avoided. Generally, fasteners are positioned at consistent intervals based on the roof’s dimensions and weight-bearing needs.

It’s also crucial to take insulation and weatherproofing around the attachment points into account. When the interface between the mauerlat and the brick wall is sealed properly, water intrusion can be avoided and the likelihood of moisture-related damage to the masonry and timber during the roof’s lifetime is reduced.

Builders and homeowners can guarantee a sturdy and safe mauerlat attachment to a brick wall by taking into account these factors and procedures. This increases the building’s longevity and general safety in addition to improving the roof’s structural integrity. Here at "All about the Roof," stay tuned for more perspectives and advice on roofing techniques!

What is Mauerlat

Knowing the function of the component in the rafter system will help you make the best choice regarding how to attach Mauerlat. Only on sloped roofs is the lower strapping belt of the rafter system, or mauerlat, present.

One component of the building’s roofing system is mauerlat. is placed around the outside wall’s perimeter as a bar or log. acts as rafters’ extreme lower support.

Constructed from a beam with a cross section of roughly 200 × 200 mm, the element serves a crucial role in the rafter system.

    Serves as a platform for fixing rafter legs or farms. During the calculation of the rafter system, the loads on the rafter legs are determined, specific values ​​change taking into account the maximum dynamic and static loads, the structural features of the roof and the physical parameters of roofing materials. Legs rest against Mauerlat and give him vertical and horizontal efforts. He must withstand them and prevent the roof fluctuations. Taking into account these loads, the cross section is selected.

For the concentrated load to be distributed throughout the entire upper portion of the wall from the points of the rafters’ supporting points, mauerlat is required.

Mauerlat provides the rafter system’s stability.

For the load to be distributed uniformly across the house’s walls, mauerlat is required.

Prices for various types of timber


For stability and safety, it is essential to fasten the mauerlat to a brick wall when building a robust roof. The mauerlat distributes the weight of the roof uniformly throughout the structure by acting as the base for roof trusses or rafters. The mauerlat must be properly fastened to the brick wall using the right anchors or bolts in order for it to endure weather and eventually support the weight of the roof. The longevity and structural integrity of any building’s roof depend on knowing the right methods and materials for this attachment.

General requirements for Mauerlat fastening

The primary prerequisite is that the element’s physical characteristics shouldn’t deteriorate over the course of the house’s operation. A number of unique construction techniques are employed in order to accomplish the goal.

    Selection of bars for Mauerlat with a margin of strength. This makes it possible to ensure estimated stability, regardless of the presence of various hidden defects of wood.

Suggested Mauerlat parameters

Wood antisepting

The second is that there is dependable waterproofing between the Mauerlat’s wooden beams and brick or concrete walls. Roofing material or contemporary non-woven waterproofing materials are typically used for this purpose.

Deciding on waterproofing

Though not always, Mauerlat is connected by means of

The Mauerlat techniques should be used when designing the house because they make the process of constructing a rafter system much easier. Furthermore, certain techniques for fixing the element are limited to the facade wall laying stages.

Ways to attach Mauerlat

The table will display the most extensive set of options, some of which are not currently in frequent use. Modern construction materials and technology make it possible to attach Mauerlat in a more dependable, quick, and easy manner.

Through the use of wooden traffic jams with equipment

We’ll choose Studs Mauerlat, for instance.

Step -by -step instructions for mounting

Prior to laying, prepare the studs. Welding the metal plate’s base together improves the security of the fastening in the hairpin’s lower portion. It can be squared up; each side measures about 6 to 8 centimeters in length. The end may simply bend at a right angle if welding is not an option. The nut size, the thickness of the Mauerlat, and the height of the brick belt masonry should all be considered when determining the length of the hairpin. In our instance, Armopome will be made up of four brick rows. 10 mm in diameter stile.

The image displays the ideal appearance of the hairpin.

Step 1: Mark the studs’ placement. It is imperative to adhere to the standard guidelines, which state that the studs should be spaced 35–40 cm from the house’s corner and have a pitch of no more than 1.5 meters.

Vital. Take care when marking up; the studs shouldn’t be beneath the rafters. Should such a circumstance arise, you will need to either modify the rafters’ steps or cut off the hairpin’s projecting ends in order to prepare the otter of the rafter leg. The reliability characteristics of the rafter system are adversely affected by both options.

Step 2: Install a metal mesh to reinforce a brick belt on the wall. The wire diameter is approximately 2-3 mm, and the cell sizes are roughly 2-3 cm. After passing the studs through the cells, place them on the labels.

We sell pantry grid in rolls and maps.

As was already mentioned, one or more studs may need to be moved in order to determine the location of the rafter legs at the same time. The strength of the Mauerlat fixation is unaffected by the distance between them, so there is no need to withstand it with high accuracy.

Sensible guidance. You should ascertain their necessity in order to facilitate the decision-making process regarding the installation of hairpins beneath the Mauerlat. The structure is kept from moving horizontally by the studs. However, these loads are not very large. The truth is that rafter farms are designed with unique components (runs, angular stops, and crossbars) that detect horizontal efforts and prevent them from creeping out. Small horizontal efforts are caused by sailboat sailing; stilettos are specifically designed to reduce the adverse effects of the wind when attaching the Mauerlat.

Step 3: Begin installing two heavy studs. Since all other elements will be displayed on them in the future, this must be done with extreme caution. The hairpin’s styling is done with such urgency.

    Prepare a cement-sand mortar. There is no need to come up with a special recipe, an ordinary masonry composition is suitable.

Homemade pantry blend

Brickwork is installed on one side of the stiletto

Furthermore, across the hairpin’s other side

Check the hairpin’s placement.

Place the hairpin at the other end of the wall using the same algorithm.

Step4: Thread or a thin fishing line should be pulled between them.

The thread-orienter must be pulled in between the extreme studs.

If you can, it’s best to give yourself a few hours to grasp; if not, you should sprinkle dry cement over the masonry solution. He’ll take in too much moisture fast, hastening the hardening process.

Both the upper and lower portions of the hairpin’s ropes need to be pulled.

The image illustrates the proper way to pull the thread.

Step 5: Attach every last stud to two ropes. As you begin to lay them, keep an eye on their location on the ropes.

Sensible guidance. If the hairpin and metal platform are welded together, it is advised to apply a small amount of solution and use it to align the components before adding a brick.

Step 6: Proceed cautiously with the wall installation, placing bricks between the studs.

The installation of intermediate studs

Small issues come up while working: the bricks need to be broken where they come into contact with the studs because the space between the hairpins is an unsightly length. This is accomplished with a special hammer; if the brick is of excellent quality and the master has hands-on masonry experience, two tools will suffice to achieve the necessary size.

Mauerlat climbs up in high heels.


Video – diameter of the hairpins for mounting Mauerlat

Integrating a mauerlat into a brick wall is an essential step in guaranteeing the longevity and steadiness of a roofing system. The mauerlat is the base onto which roof rafters or trusses are fixed. It is usually a horizontal beam made of wood or metal. It is necessary to use the right techniques to distribute the weight securely and evenly when attaching it to a brick wall.

First and foremost, it’s crucial to determine where on the brick wall the mauerlat should be attached. Finding load-bearing locations and confirming that the wall can sustain the weight of the roof structure are common steps in this process. This is usually accomplished by positioning the mauerlat directly above the building’s supporting columns or walls.

Second, the roof’s stability is greatly influenced by the attachment technique. Heavy-duty bolts or anchors are frequently used to fasten the mauerlat to the brick wall. These anchors provide a strong connection that can bear the weight and forces applied by the roof by penetrating deeply into the wall’s structure.

To guarantee that the mauerlat is securely fastened, the attachment points must also be spaced and aligned properly. This lessens the chance of uneven stress over time, which could damage the integrity of the brick wall and the mauerlat. It also helps to distribute the load evenly across the wall.

To ensure the structural integrity of the entire roof system, attaching a mauerlat to a brick wall requires careful planning and execution. In order to give homeowners peace of mind and guarantee safety for years to come, builders can create a sturdy and long-lasting foundation for the roof by adhering to the right guidelines for positioning, attachment techniques, and spacing.

Video on the topic

Mauerlat on the brick wall.Mauerlat on a Brick Wall

Murlat mount

Mauerlat and rafter mount

So that the roof does not go! 3 ways to fix Mauerlat

What do you think, which element is the most important for a reliable and durable roof?
Share to friends
Denis Shcherbakov

Professional roofer with 20 years of experience. I know everything about the installation, repair and maintenance of various types of roofs. I will be happy to share my knowledge and experience with you.

Rate author
Add a comment