Nails for Ondulin: an overview of the types and rules of their use + home -made modifications

The selection of appropriate nails is essential for guaranteeing longevity and stability when it comes to roofing materials such as Ondulin. In order to keep your house weatherproof, Ondulin sheets must be securely fastened to the roof structure with nails. The longevity and performance of your roof can be greatly affected by knowing the various nail types that are available and how to use them properly.

Because of its composition, ondulin, a lightweight and long-lasting roofing material composed of cellulose fibers and bitumen, needs special nails that can penetrate and hold firmly. The incorrect kind of nail can cause problems like leaks, wind damage, and early wear and tear. Consequently, it’s critical to choose nails that complement Ondulin’s special qualities.

For Ondulin roofing, a variety of nail types are appropriate; each has unique qualities and uses. Typical choices include aluminum nails, which are noted for being lightweight and non-corrosive, and galvanized steel nails, which are resistant to rust and corrosion. The decision between these types is influenced by elements including the budget, roof pitch, and climate in the area.

It’s critical to adhere to precise nail placement and spacing guidelines when installing Ondulin sheets. Nails should normally be hammered into the sheets’ corrugated valleys to guarantee a tight fit and stop water intrusion. When nails are spaced correctly, the weight is distributed more evenly across the roof, reducing the possibility of damage during severe weather.

Knowing how to adjust or modify nails for Ondulin can be helpful for individuals thinking about doing their own repairs or modifications. Creating custom nail heads for improved grip or utilizing different materials for longer durability are examples of home-made modifications. To preserve the effectiveness of the roof, it is imperative to uphold the integrity of the roofing system and follow manufacturer guidelines.

Review of professional types of nails

The guidelines for installing the Ondulin roof always specify that only branded nails wearing plastic hats should be used to secure the sheets. The manufacturer claims that this is the only method for achieving high-quality, sealed fastening, and that only a formal warranty is offered for such a roof.

Climate, bitumen sheet characteristics, and the fact that a hammer will strike the nail heads are all taken into consideration when selecting the material and shapes of these nails.

Finally, what exactly is Ondulin? This cellulose has been heavily loaded with mineral fillers and bitumen. This material is very strong and resistant to moisture, and it has a shape similar to a regular slate with waves. Ondulin sheets are delicate in the frost and relatively soft—sometimes even too much in the heat. Given all of this, standard roofing screws or nails with short hats are just inappropriate for this type of roof’s apparatus.

Ondulin’s professional nails are always done with large hat fields and for no reason at all. She manages to hold sheets in strong wind gusts. Furthermore, the hat shields the metal rod from moisture. These days, standard nail color hats are made in black, green, red, and brown so that they "get lost" against the backdrop of an average ondulin roof.

Depending on the manufacturer, caps for these nails are either made of polypropylene (PP) or polyvinyl chloride (PVC). The qualities of these two types of solid plastic are nearly identical and of excellent quality.

Their protection against UV radiation is effective in practice, and their strength characteristics do not diminish over time. Consequently, even with sufficiently strong wind gusts, the tightness of the roof won’t be compromised if you use the Ondulin professional nails.

These nails’ precise specifications are as follows:

Additionally, the rubber gasket in Ondulin’s professional nails has a unique curved shape that fits the waves perfectly. Additionally, carbon steel is used to make a portion of the nail’s basic component. To provide a nail with corrosion resistance, a passivated zinc solution is applied to it in the factory.

Additionally, a unique thread is affixed straight to the rod on the nail. This makes the rod easier to jam firmly into the crate and pull it back, though there is still an issue with that. Once more, it is effective against wind gusts.

For each sheet, the manufacturer advises using a total of 18 to 20 of these nails (more exact instructions are always attached to the roof).

Car beams with opening caps

For over fifteen years, snapping hat nails were actively sold and fastened to roofs; however, their renown has nearly evaporated in the modern era. They were imported, just like Ondulin himself, once.

However, considering how many people complained about the lids, they were successfully replaced with monolithic when Ondulin production in Russia itself was improved. Despite this, "Stroybat" brand nails are still available in construction supermarkets and are in high demand.

And this is how they appear:

This is how one goes about using such nails. Lift the lid, jam the nail into the Ondulin leaf, and manually snap the roof:

The manufacturer always made it clear in his instructions that a hole needs to be made under the center of the nail in order for a plastic cap to be properly placed on it. Next, simply close the lid with a small amount of force.

If all goes according to plan, there will be a tiny click:

The catch is right here. Furthermore, the covers aren’t always "wanted" to close! especially if they were low-quality and purchased from an unidentified seller somewhere on the market.

Then, after numerous tries and haphazardly broken covers, customers fervently desired that the person who created this knowledge attempt to close up to 1000 of these nails at least once. However, that is the exact amount that covers the typical residential building’s roof.

The knowledgeable and experienced builders took special care to lower the plastic lid into the hot water in order to solve this issue. It was the simplest method. Overall, the roofer’s patience was tested by this fuss.

Ultimately, there were instances when it got to the point where only one out of ten hats broke for the first time. Afterwards, roofs that didn’t work had to be abandoned and their nail caps sealed with a material that matched the roof’s color.

New nails with monolithic hats

It is now advised in Russia to affix Ondulin with monolithic hats using nails. In this instance, the procedure is significantly simpler: tap the hat with a hammer until it makes contact with the sheet’s wave. No breaking covers, troublesome nails, questionable quality, and grievances.

Examine the complete list of these components:

The primary responsibility for installing Ondulin on these nails is to score them straight into the crate:

Additionally, hurrying the sheets to be fastened on the ground—rather than by eye—is required for the nail to fall into the crate. Additionally, it will help if you stretch the rope or draw a line in the appropriate locations beforehand.

Not artisanal production, but high-quality fastening is required so that the nail enters the wave correctly. Since the coating can only be obtained from reliable vendors, it is therefore preferable to buy professional ondulin nails from the same location. Although the cost of these fasteners is slightly higher than that of regular roofing nails, their requirements are entirely different.

And now for the actual process. When clogging a nail with a monolithic hat, it must be held rigidly vertically and without distortion by the rod. It’s also crucial to avoid scoring a nail too deeply.

In actual practice, proceed as follows: after using a hammer to lower the nails until they are in contact with the leaf’s surface, gently press the sheet against the crate in this location with your hands, then make a slight adjustment to the hat. As it happens, you won’t have to follow the mount exactly in the ondulin. The hat’s bottom should, by all means, snugly fit the wave’s bend.

All of this is readily apparent here:

It would appear to be very simple! What kind of nails should I use to fasten Ondulin? It’s obvious how to work with them, so why is it in foreign video instructions that self-tapping screws, not nails, are used? Does Russia follow a similar custom? This is fascinating!

Self -tapping screws for Ondulin: Western experience

Ondulin repairs are customary in our nation, but self-tapping screws are more commonly used overseas. Since the primary goal is to make sure that the ondulin fastener consistently holds on the crate and that its parameters are sufficient for this, you can also attempt this method. Thus, choose self-tapping screws as long as the nails from the manufacturer if you wish to use them.

Of course, unless you purchase professional nails made especially for this material, not a single Odulin vendor will suggest that you utilize a different solution. However, self-tapping screws are utilized equally frequently at the same level as nails in work involving the same Ondulin abroad:

What are the actual benefits of self-tapping screws over nails? Therefore, in the event that you unintentionally pull the mount, the hat will close without issue if the screw is manually turned slightly.

Roma believes that using a screwdriver is far more convenient than hammering if working in the summertime, when Ondulin’s composition causes it to soften slightly. As you can imagine, you will need to score approximately a thousand nails in stages in order to cover the roof of 3×6 slopes. You won’t want to pick up a hammer for a while after doing such work!

Self-tapping screws are still available in Russia, despite their declining popularity. Additionally, regular roofing—like "stelphic" roofing—that has a specific rubber layer applied to it is appropriate for this use.

The second thing to note is that these self-tapping screws need to be coated against corrosion in order to prevent issues and save roof repairs.

Lastly, if you choose to fasten the sheets to the metal crate, self-tapping screws are a must. The nail is no longer for scoring, after all! Additionally, the ondulin manufacturers permit and occasionally even suggest using a metal base.

To determine how many self-tapping screws are needed for an ondulin, begin with the fact that the standards state that this type of roof should be able to withstand winds of up to 175 km/h. As a result, there should be sufficient mounting points—between 18 and 20 per sheet. It makes sense to be concerned about reserve as well.

"In the roofing industry, selecting the proper nails for Onduline sheets is essential to guaranteeing their efficacy and longevity. This article offers a thorough explanation of the nail kinds that work well with Ondulin as well as helpful advice on how to use them. It also covers a variety of do-it-yourself upgrades that can improve the installation procedure and lifespan of your roof, providing helpful advice for pros and amateurs alike."

Hat damage: why is this happening?

In the event that you encounter a fake, you are first and foremost at risk from something as inconvenient as cap cracks. This is unfortunate because it means that the nail will have to be removed and replaced.

But even with expert nails, damage can still happen if they’re not careful:

Ondulin’s nails can become damaged for multiple reasons at once:

  • Reason No. 1. The nail was not completely driven, and now the cap does not snap. To fix this, the builder just hits it with a hammer.
  • Reason No. 2. The hat is monolithic, but it hit it too much. Even high -quality plastic has its own limit.
  • Reason No. 3. All mount – fake. Let us explain in more detail. In the nails of artisanal production, even a hat – from another material. In the branded fastener, the cap is made of high density polyethylene, so it has good resistance to shock exposure and temperature differences. All these properties have no fake, and therefore their hats are destroyed with any enhanced load.
  • Reason No. 4. You scored a nail not deep enough. At the same time, the cap skirt has not changed in geometry, and therefore the cap does not close and it beats too much on it again.
  • Reason No. 5. The nail was not driven perpendicular to the crate. In a word – crooked. In this case, the cap’s skirt did not press the wave of the wave completely to the crest, and the nail now has to drive much deeper than necessary.

Try to adhere to the following guidelines to avoid all of this during installation and to prevent your work from becoming the tedious task of pulling out the nails again:

  • Rule No. 1. Always drive nails only strictly perpendicular to the plane of the bars of the crate.
  • Rule number 2. Never beat too much, remember the limit of the strength of the hats.
  • Rule No. 3. Do not squeeze and do not stretch very ondulin when you lay it. Otherwise, the profile of the sheet will be distorted, and the hat will simply fall on the crest of the wave of not the whole plane. This is fraught with impaired waterproofing.

Naturally, make sure the nails themselves are real as well. The corporate nail is always rolled into a ring cone shape, which makes it easy to identify from imitations. The word "ONDULINE" is inscribed convexly on the umbrella-shaped skirt of the cap.

Folk modification of nails

A good master is in his hands, as they say. What should you do if your nails were too short for a specific crate but you still wanted to use gorgeous, salon-quality nails for ondulin?

This is the method of superimposing the people:

Naturally, re-doing such nails would be quite the hassle. After all, replacing the rod was all that was needed to start with the hats opening. It’s true that she wouldn’t close in that situation since the nail hat couldn’t converge with the plastic hat. Additionally, in this option, Ondulin’s nail stays the same; only a new format appears.

The performance and longevity of your Onduline roofing project depend on the nails you use. Because onduline sheets are flexible and lightweight, proper nailing requires a particular kind of nail. The incorrect nails can cause damage, leaks, and even early roof failure.

Choose stainless or galvanized steel nails when choosing nails for Onduline. Because of their resistance to corrosion, these materials won’t rust over time, protecting the structural integrity of your roof. Furthermore, even in inclement weather, the Onduline sheets remain firmly in place thanks to the strong hold that these nails provide.

Make sure the nails you select are the proper thickness and length. Overly long nails have the potential to puncture through the underside of the sheets and cause leaks, while nails that are too short may not pierce the roofing material sufficiently. To guarantee correct installation, refer to the manufacturer’s instructions for the suggested nail specifications.

When making do-it-yourself adjustments or fixes, think about using plastic or rubber washers with your nails. In order to further prevent water infiltration into your roof, these washers can help seal around the nail heads and offer extra waterproofing. This easy upgrade can greatly increase the life of your Onduline roof.

You can guarantee that your Onduline roof will stay sturdy, long-lasting, and weather-resistant for many years to come by realizing how important it is to use the proper nails and by adhering to these recommendations.

Video on the topic

How to get a nail from Ondulin?

Which nails to choose for electrical installation?

Nails, what to use for what.

The better to fasten ondulin? Screw or nail.

119. The nails ondulin

A nail for Ondulin. Design, application. www.Maysterfix.Com

What do you think, which element is the most important for a reliable and durable roof?
Share to friends
Alexander Sorokin

The owner of the roofing company, an expert in the roofing markets. I'll tell you about the novelties of the roofing industry and help you choose the best option for your home.

Rate author
Add a comment