DIY drain from the roof

Effective rainwater management is essential to preserving the integrity and lifespan of your roof. Installing a do-it-yourself drain system is one efficient way to accomplish this. Redirecting rainwater away from your roof with a do-it-yourself drain system helps shield it from possible leaks and pooling damage. There are easy steps you can take to improve the functionality of your roof at a reasonable cost.

It is crucial to evaluate the existing drainage pathways and the structure of your roof before starting to install your DIY drain system. Look for places where there is poor drainage or where water tends to collect. Finding these points will help you decide where to put your drain and make sure that the water flows as efficiently as possible.

The components required for a do-it-yourself roof drain system are easily obtained and reasonably priced. PVC piping, connectors, a collection basin, and simple tools like a saw and measuring tape are usually needed. Even for individuals with little DIY experience, these materials are simple to work with and can be found at your neighborhood hardware store.

The first step is to measure and mark the location of the drain installation. Make sure the placement permits adequate drainage away from your home’s foundation. Once the drain’s path has been marked, carefully cut through the roofing material and any underlying layers. During this process, take care not to damage the roof structure.

Subsequently, put the PVC pipework together in accordance with the design. Make sure the piping is securely fitted with waterproof seals when connecting it to the collection basin. The piping should have a slight but sufficient slope to help water flow in the direction of the drain. Verify every connection twice to make sure there are no possible leaks that could jeopardize your system’s performance.

To make sure the drain system is operating properly after installation, run water through the pipes. Keep an eye on the flow and look for any indications of leaks or insufficient drainage. Adjust as needed to maximize efficiency and guarantee that water is properly diverted off the roof.

For your DIY roof drain system to function well over time, maintenance is required. Check the pipes and drain on a regular basis for obstructions or debris that could prevent water from flowing. In order to avoid blockages and guarantee uninterrupted drainage during times of intense precipitation, remove any obstacles and thoroughly clean the collection basin.

By taking the effort to install a do-it-yourself drain system on your roof, you prolong the life of your roof and shield your house from possible water damage. This affordable solution improves the overall durability and functionality of your roofing structure while helping you manage rainwater effectively.

Materials Needed:	plastic gutter, downspout, brackets, screws, sealant, measuring tape, hacksaw
Steps:	1. Measure and mark where the gutter will go. 2. Cut the gutter to size using a hacksaw. 3. Attach brackets to secure the gutter in place. 4. Connect the downspout to the gutter. 5. Seal joints with waterproof sealant to prevent leaks.

What can you make a drain from the roof with your own hands

To manufacture the device with your hands, you can use a variety of materials.

Galvanized sheet steel. A very good choice if there are special devices and machines for the manufacture of pipes, knees, funnels and other structural elements. In addition, it is necessary to have experience with the work of a tin or at least have an idea of ​​such a production. Most ordinary people with tin work are unfamiliar and leaf galvanized steel for the manufacture of drainage systems are rarely chosen.

Drain the steel roof.

Bottles made of plastic

A plastic drain illustration

There are objective reasons for this situation.

1. The first – sewer pipes are made of the cheapest plastic, most often not primary, but secondary, they are not affected by hard ultraviolet rays, they do not freeze/thaw, mineral dyes are not added to improve the design type.
2. The second – well -known manufacturers of drainage systems set additional margins for the promotion of the brand. Sewer pipes do not concern.
3. The third – excellent forms and appearance significantly complicate the production of drain. It is necessary to have special machines and accurate multi-component press forms, a set of devices has many dozens of units. The fourth – high quality is maintained and due to the control of the process at each stage of production. This causes an increase in marriage and, accordingly, increases the selling cost of products.

The only feasible option is to make the roof plum yourself using sewer pipes, which we will discuss in detail and provide step-by-step instructions for in this article.

What function should the drain perform

Whatever material the drain is constructed of, it must shield the house’s base and foundation from precipitation and melted snow.

The drainage system is required to divert and collect rainwater and melt snow.

Wolly land can prematurely deteriorate building materials or the foundation’s ability to sustain itself. Diminishing the foundation’s supporting indicators is a major issue. It is only visible when fractures show up in the house’s facade walls. Restoring the foundation’s strength is a very expensive and difficult task that should only be done by experts. However, they are unable to provide a 100% assurance that the actions taken will result in the desired outcome. The lifespan and safety of the structure’s operation are unaffected by any of the other drain functions, which include collecting rainwater in a container and decorating the structure.

The choice to arrange the drain

Prices for drains

Drains

We’ll walk you through all the necessary steps to properly manage rainwater runoff in our guide on building a DIY roof drain. We enable you to protect your home from potential water damage while extending the life of your roof, from choosing the right materials to knowing local regulations. Whether you’re an experienced do-it-yourselfer or a first-time homeowner attempting to take on this project, our simple instructions guarantee that you can obtain a dependable and useful drainage solution catered to your requirements."

Step -by -step instructions for manufacturing gutters from sewer pipes

Prior to beginning work, a few technical issues should be resolved. This will help to improve the structure’s performance and prevent annoying errors.

Components of a homemade drain assembly

Gutter and pipe tags

Drainage system components

We pay close attention to the function and operating parameters of every spillway component because this information will help to prevent mistakes when producing structures independently.

Step 1: Get supplies and equipment ready. Although most factory systems are made with a diameter of 100 mm, pipes with a diameter of 110 mm are quite suitable for the drain. Most houses use these universal dimensions. If the area has an excessively steep slope, you can place multiple water-draining funnels on a single gutter segment, spaced roughly 6 to 8 meters apart. Sewer pipes are typically 2.5 meters long and made of polypropylene.

Prices for polypropylene pipes for sewage

Polypropylene pipes for sewage

Vital. You must be aware of the distinctions between internal and external sewage pipes.

Some inexperienced masters think that the pipes for external sewage are not afraid of ultraviolet rays and negative temperatures, because they are mounted outside the house and are connected to external highways. Everything is correct, these are pipes for external sewage, only they are installed in trenches, and not in the open air. And there are no UV rays and negative temperatures in the trenches, but there are additional mechanical loads. In order for the pipes to be maintained, they have thicker walls and, accordingly, much higher price. Additives from the negative effects of ultraviolet rays of pipe pipe do not have. For drains it is better to buy pipes for internal sewage, they are noticeably cheaper.

Determine the pipe’s meter while also ascertaining the building’s height and length. One pipe is used to make two gutters. Find out right away how many turns there should be and at what angles, how many drives there should be with different rotational angles, and how many tees and plugs there should be. Sewage pipes cost between 150 and 200 rubles per meter, and ten meters of drains, including all extras, come to about 1,500 rubles. The cost of this is ten times less than that of the factory spillway system.

Sewer pipe fittings

To function, an electric circuit machine and multiple thin metal disks with the appropriate diameter are required. Select the tiniest grinder available. It is not necessary to use a high power plastic cutter, and using a light grinder is far more convenient.

Get ready a measuring tool, a metal bar, a locksmith, a ruler, and a roulette. Pre-drawing a sketch and going over and calculating everything again is a good idea.

Metizes required for pipe connections

Sensible guidance. Initially, attempt to construct a DIY drainage system for non-incompatible structures, such as garages, bathrooms, workshops, etc. D. You will learn from this experience and discover how the object is viewed by the system during this time.

Step 2: Set up the workspace. The pipes are lengthy, so you must consider how to cut them in one location. The cut will never be even if it is inconvenient to work. Since this is an open marriage, it will either need to be corrected, which is very time-consuming. Alternately, add such a groove to the structure in a discrete location. Using regular pallets for work is incredibly convenient. Longitudinal sawing is made much easier when the pipe rolls into and is held firmly in the space between the boards.

Provide a different location for the finishing touches and materials that have been purchased, set up a table for tools and hardware, and address the lighting problem.

Step 3: Put a plastic stopper in the pipes’ ends. The plug will not stay in place when the pipe is later split into two parts beneath the gutter. Use self-tapping screws to secure the element to keep it from falling out. The screws are approximately one centimeter long. There must be four pieces total, spaced symmetrically apart. There should be two self-tapping screws left on each gutter after the pipe has been cut. Ensure the screws are not situated in close proximity to the cutting line.

And yet another subtlety. The plug is sealed by a rubber ring that is fitted into the pipe’s end. Self-tapping screws need to be positioned so that the trumpet of pipes is pressed against the rubber ring rather than being damaged by them. Retract from the end by roughly 3–4 cm; measure this exact distance yourself; variations in pipe quality among manufacturers may cause it to vary slightly.

Step 4: Attach tags so that the pipe can be cut in half. A pencil does not draw on plastic; it is indicated with a felt-tip pen.

Drawing a straight line the whole length of the pipe

Step 5: Carefully cut the pipe along the indicated line. As was previously mentioned, one hand should be used to hold the grinder while the other is used to fix the pipe. As the pipe is dripped, the pipe moves to the instrument. You must call an assistant if working that way proves to be difficult. Allow him to hold the pipe while the master uses two hands to operate the grinder. It is advised to use the tool in this manner for safety instructions, by the way.

Divide the pipes in half.

Step 6. Remove the burrs. The disk does not cut plastic, but melts it, there are large burrs, they are removed easily. Some use special disks for grinding, put them in a grinder and try to remove molten plastic from the edges with their help. We do not advise doing this, the disk will remove the old burrs and leave new ones, the plastic melts from large revolutions. Work without a tool, burrs are cut off without problems with an mounting knife or break off with their hands, But you have to make significant efforts. The third option – take an abrasive disk and work with it manually. If your cut turned out to be wavy, then it is advisable to trim it. Do not be very upset, the next pipe will be cut much better and easier, and a slightly spoiled gutter can be put on the back of the structure, no one will see it there.

The workpieces must have the burrs removed.

Proceed with the cutting of all the remaining gutter pipes based on the same algorithm. Additionally, two gutters are joined by self-tapping screws. The overflow locations require the installation of half of the factory rubber gasket; these have been designed with technological grooves for this purpose.

Two gutters connected

The sections of the connection of the gutters are the most dangerous, it is here that the leaks most often appear. The fact is that the gutter has a large length, insignificant efforts at one end through the fasteners increase tens of times, they work like a lever. The second end may shift a little. In order to completely eliminate the likelihood of leaks, we strongly recommend using the sealant. You can buy cheap, there is no need to use the stability resistant to ultraviolet rays, the material is not in the open air, a half of the plastic pipe lies on top and protects it. But you should pay attention to the indicators of adhesion and plasticity.

Sewer pipe sealant

You can start creating more intricate spillway system components now that you have some experience.

Production of a funnel

Among the system’s most intricate components is this one. To manufacture it, you must get ready:

• the pipe segment of the desired length;
• end plug;
• turn;
• Connecting cross.

Step 1: Combine all the components into a single design and measure the pipe segment’s length once more.

Step 2: As we previously mentioned, use self-tapping screws to secure each individual detail.

Vital. Always use a sealant to lubricate the connected surfaces; don’t rely solely on rubber seals.

Step 3: Carefully locate the center of the structure and draw on both sides of the line.

Step 4: Use a grinder to cut the assembled design on the lines.

Take out the burrs. Take your time and do not rush. See to it that no parts move independently while being cut.

Sensible guidance. It is preferable to leave the gutter plugs whole rather than cutting them in half because they are held in place more firmly that way. This is accomplished by cutting off half of the pipe’s trumpet around the circle rather than cutting it along the axis. Such a gutter looks different from the norm; decide for yourself what kind of connection to make.

Smoothing the workpiece’s end

Tig using a funnel

A storm will receive the redirected water. Rainwater is always helpful in the summer cottage and is thought to be very beneficial for watering all plants. particularly if there isn’t a centralized water supply.

Now that almost every component of the spillway system is ready, you can start making the metal brackets.

Prices for popular models of screwdrivers

Screwdrivers

Production brackets

A metal strip that is up to two centimeters wide and 2.0 mm thick must be ready.

Step 1: Determine the brackets’ length. It is equivalent to half of the gutter’s circumference and the site’s length, which is fixed to the rafter system. It is advised to use a soft wire to avoid making a mistake. Turn it into a template and reposition it multiple times to get the best result. Align the wire and measure its length; everything is normal. In any case, it is recommended to add a supply of roughly 2-3 cm.

Step 2: Cut the blanks for the brackets and make tags on a long strip. Drill holes in them.

Plum installation

Installing the structure on the roof assembly is possible if the slope is short and someone is available to help. Attach the brackets to the gutter on the ground. Work with extreme caution as installing it could break the assembled groove. Remember to create a slope, roughly ten linear meters or two to three centimeters, to collect water. No longer required; otherwise, water won’t be able to enter the groove because it will move too much away from the roof at the opposite end.

Gather drainpipes, fasten them to the tree, and insert the other end into the rainwater collection container. Any clamp will hold vertical pipes to the walls; tightening the clamps is not required. Clamps should ideally be positioned so that they press up against the bell protrusions.

You can attach plastic pipes to any nearby vertical racks by wrapping them with tape.

Sensible guidance. Screws at the connection site should be used to fully eliminate the possibility of depressurization of vertical pipe joints. They refuse to let pipes topple over from their own weight.

Production hook

The gutter description method mentioned above is thought to be extremely dangerous; instead, it is advised to use the conventional method, which involves fixing the hooks before installing the gutters on them. However, accurately bending homemade metal stripes is a challenging task. You can create the most basic device "hooks" to make the process easier.

Two 30- to 40-centimeter-long square pipe segments are needed for this task. The pipes’ cross sections need to be chosen so that there is a 6 to 8 millimeter gap between them when they insert into one another. For instance, one pipe has a width of 30 mm, while the other has a width of 20–25 mm. Make sure to thoroughly clean the pipe ends, eliminate any burrs, and align the planes.

Step 1: Insert the pipes into one another, making sure that their ends line up and that they are in the same plane.

Joining of two pipes

Step 2: Insert the bracket into the space between the pipes to adjust the gap’s size.

A bracket is placed in the opening.

Sensible guidance. It will be simpler to operate the device if the gap’s width is just a little bit wider than the metal bar’s thickness. Not every metal strip is flawlessly straight; some have tiny bends. They will be able to bend their device without any issues with a larger gap. It is advised to place a piece of sheet iron over the plank that is approximately 1 mm thick in order to obtain these dimensions between the device and the metal strip. It is removed by welding after being picked up.

Beneath the bar is a 1 mm thick piece of sheet iron.

Grasp the pipes with electric welding in the dumb’s lower section and repeat the process from the other end.

Welding connects the details.

Step 3: Take out the bracket and weld the pipes firmly. Take off the warden’s clothes.

The gadget is prepared for usage. Dealing with him is a breeze. After inserting the workpiece on the mark into the hook-bunch, the part is bent at the proper angle and removal using one hand while the other holds the device.

Fixing brackets for gutters

Inserting the bracket into the hook

Prefabricated bracket

With hooks, you can bend in an even manner as well as under different slopes. In order to accomplish this, the workpiece should rotate slightly in one direction rather than pressing up against the side wall. The bending angle varies with the rotational angle. Experience seems to indicate that, with time, all hooks are precisely bent to match the designated sizes, accounting for the characteristics of the drainage system and the roof.

Self-made drain fastening

For homeowners wishing to enhance water drainage and safeguard their property, building a DIY drain from their roof can be a useful and satisfying project. You can efficiently control rainwater runoff and avert possible damage to your roof and foundation by installing a roof drain.

It’s important to comprehend the fundamentals of roof drainage before starting this project. To choose the best spot for your drain, evaluate the slope and design of your roof. Make sure you have the pipes, connectors, waterproof sealant, and other tools and supplies you’ll need.

Pay close attention to the manufacturer’s instructions and take local building codes into account when installing the drain. In order to guarantee that the drain works efficiently and prevent problems like leaks or insufficient drainage, proper installation is essential.

Just as important is keeping your roof drain clean. Maintain regular drain cleaning and inspection to avoid blockages caused by debris like branches or leaves. If you want to reduce debris buildup and increase the longevity of your drain system, think about installing a filter or grate.

All things considered, installing a DIY roof drain can be a wise investment in preventing water damage to your house. By carefully planning, installing, and maintaining your system, you can improve drainage efficiency and extend the life of your foundation and roof.

Video on the topic

DIY drain from PVC pvc roof.

The groove is tested by time!

The drain for 300 rubles 9 meters from the profile for drywall Part 2

How to make the most budget drainage

Why you can not make a plum from a plastic pipe?

Gutter gutter from a sewer pipe, simple and cheap!

A simple version of the drain system for the roof from sewage pipes