End bar for metal tiles: what, why, how?

The end bar is essential to achieving a safe and well-polished finish in metal roofing. The end bar is specifically made for metal tiles and has an aesthetic as well as functional value. It’s an element that improves the overall appearance of your roof while also adding to its resilience to the elements and longevity.

Now, describe an end bar in detail. It functions essentially as a finishing piece to give a clean edge and stop water seeping in by covering the exposed ends of metal tiles. This is especially crucial in regions that frequently experience high levels of precipitation or snowfall, as proper sealing is necessary to preserve the structural integrity of the roof over time.

Why is the end bar required? The main purpose of it is to stop water from leaking under the tiles. It forms a barrier by firmly covering the ends, ensuring that any water dripping off the roof surface is diverted away from weak spots. This helps to preserve the building’s insulation and structural integrity in addition to shielding the roof from possible water damage.

How is an end bar operated? The end bar is typically constructed from sturdy materials like stainless steel or aluminum and is intended to survive the harsh conditions found on a roof. It is put in place to give a clean, polished finish along the roof’s edges where the metal tiles end. Effective installation is essential to achieving a tight seal that improves your metal roof’s functionality and appearance.

Why do you need a end bar

The end bar is a necessary component of the metal tile roof. It is mounted above the roofing on the front-to-back overhangs of the roof and:

  1. Protects roofing from breaking the wind. Without the end plank, the wind directed to the pediment of the house will raise the edge of the roofing, causing its vibration. Over time, this will lead to a weakening of fasteners and the development of brown corrosion along the edge of the holes. The stormy wind can completely disrupt the extreme sheets of metal tiles. Therefore, the end bar for metal tiles is often called wind.
  2. Prevents moisture from getting into the roofing pie from the sideboard. During heavy rain, the wind can blow water inside the roof pie through the pediment. The end bar closes the pediment of the roof and prevents this.
  3. Prevents the penetration of birds and rodents into a burden. Through unprotected ends to the roofs, it is not so convenient to get into the roof as it is convenient as through cornice overhangs. However, in some cases, pedimental overhangs can also become a point of their penetration. Especially if the metal tiles have a high profile.

End strips also have a significant aesthetic impact on a metal tile roof. They visually complete the roof and close the leaf’s wavy edge, giving it a more harmonious and symmetrical appearance.

When it comes to roofing, metal tile end bars are essential for both practicality and style. It secures the tiles in place and serves as a protective cap around the edges of metal tile roofs to stop water intrusion. It is essential to comprehend its installation and purpose if you want your roof to last a long time. This article delves into the definition, significance, and installation process of end bars, equipping both roofing experts and homeowners with the necessary knowledge to maintain long-lasting and aesthetically pleasing metal tile roofs.

Types of end planes for metal tiles

Even though the task is straightforward, different manufacturers’ end strips for metal tiles can have quite different profiles.

It’s just a corner bent under 90 degrees in the middle in the most basic scenario. Simultaneously, one edge bends bluntly inward, and the other bends outward. The bent edge will function as a chipper during rainy conditions, releasing water from the wall.

One coating comb should be fully overlapped by the shoulder of the end bar, which begins on the metal tile. However, some reinforced strips—whose shoulder can cross over two ridges—are made to be installed in areas with heavy snowfall and frequent thaws. This offers incredibly dependable defense against moisture infiltration from the roofing side. Even though the capillary effect causes the water to drag beneath the end bar, it simply drains along the metal tile’s wave’s bottom without endangering anything.

It is advised to use end strips with stiffeners soldered on their shoulders in areas with strong wind loads. It may take the form of tiny grooves or a complete trapezoidal profile. The end bar can better withstand the wind load thanks to stiffener ribs.

Additionally, there are unique end strips designed specifically for metal tiles. They are named stepped because of their distinctive shape—the end bar mimics the metal tile’s step pattern, making it much more compatible with the roofing.

The stepped end bar seems to be the best choice for metal tiles at first glance. But there are a few asterisks:

  • Steping end planks are significantly more expensive than ordinary, even enhanced;
  • They are more complicated in installation, since, as a rule, each step is a separate element that needs to be correctly joined and stacked;
  • The dimensions of the stepy end bar must accurately correspond to the length of the step of the metal tile, therefore they are released for a specific profile and are not interchangeable.

Stepy ending planks are rather unusual and characteristic of a proprietary metal-level metal level because of all these "buts." Such a prerequisite element cannot be applied to a large product.

For metal tiles, all end strips are covered with both long edges, regardless of the species. This increases the element’s rigidity and shields the metal from brown corrosion.

Installation of the end bar

This prescription element is easy to fasten if step-out end strips are left behind the brackets. Before installing the ridge corner, install the end bar following the completion of the cornice overhang decoration. Simultaneously, prior to actually fastening the bar, you must:

  • Install a wind board;
  • fix the seal on the metal tile.

Standard wind board section, measuring 100 x 25 mm. However, its measurements are flexible; the board’s width should be the same as the end bar’s vertical shoulder less any bent debris.

The windbreaks extend above the metal tile wavelengths and are fastened to the end of each bar of the crate using ruffled nails. The easiest way to find the ideal wind board position is to try the end bar on it. The prescription element should then be positioned so that it nearly touches the metal tile’s surface. This is crucial: there should never be a large space between the end bar and the roofing.

In the event that thin boards are utilized for the crate, metal corners are used to fasten the wind board to the rafters via the beam-lining. Regardless of the method used, the waterproofing film is bent on the crate’s ends at the same time. Next, it covers the windbreaker and the ends are secured with a construction stapler.

The seal is attached after the wind board is installed. It is necessary to soften vibration and seal the space between the end bar and the metal tile so that the edge of the extra element cannot harm the roofing’s decorative and protective surface. On the upper shoulder of the bar, the universal seal is glued as near to the bend as feasible, but not quite there.

Installing the end bar itself is now necessary:

  1. Installation of the bar begins by the cornice overhang.
  2. It is advisable to cut the edge of the first end bar and bend so that it closes the comb of the metal tile.
  3. The bar is aligned and fixed: roofing self-tapping screws to the windboard in a checkerboard pattern every 10-15 cm; metal screws – to the crests of metal tiles.
  4. Between the metal tile and the upper shoulder of the end plank, as well as between the frontal board and its lower shoulder, a sealant is applied, preferably, polyurethane. This will help make the knot more sealed. It is important that the sealant is between the board and metal. This means that waterproofing must be cut so that between its edge and the edge of the shaped element is 3-4 cm.
  5. The overlap between the second and the subsequent end strips should be 5-10 cm. For reliability, it is also smeared with sealant.

Never allow self-tapping screws to pass through insulation as this will cause brown corrosion to appear quickly where fasteners are located.

Maintaining the longevity and integrity of your roof depends on your understanding of the significance of end bars for metal tiles. These tiny but essential parts keep the edges of metal tiles in place during severe weather by keeping them from lifting or coming loose. End bars give your roof a secure finish, which adds a lot to its overall longevity.

The ability of end bars to improve the visual appeal of your roof is one of the main reasons they are necessary. By carefully hiding the exposed ends of metal tiles, they produce a polished and tidy appearance that improves the building’s or home’s overall curb appeal. This meticulous attention to detail raises the property’s value in addition to enhancing its aesthetic appeal.

End bars are easy to install; just carefully position them at the edges of the metal tiles and fasten them with the proper fasteners. This reduces the possibility of damage from wind uplift and other environmental factors by guaranteeing that each tile is securely held in place. A skilled professional’s installation is essential to guaranteeing your roof’s long-term security and functionality.

In conclusion, end bars might not seem like much, but they are crucial to the overall design and operation of a metal tile roof. Both homeowners and builders can make decisions that enhance the long-term resilience and visual appeal of their roofing systems by being aware of what end bars are, why they are needed, and how to install them.

Video on the topic

This must be done during the installation of metal tiles!

How to make an end bar for metal tiles

Installing corrugated board on the roof with your own hands Part 4 installation of the end plan

Installation of end planks. How to sew a oving roof with metal with your own hands?

What do you think, which element is the most important for a reliable and durable roof?
Share to friends
Gleb Zuev

Exterior designer, author of books about roofing materials. I will help you make your roof not only reliable, but also beautiful.

Rate author
Innfes.com
Add a comment