How to calculate the corrugated board on the roof

One of the most important steps in installing corrugated metal roofing is figuring out how much corrugated board you’ll need. You’ll save time and money by purchasing the correct quantity of materials thanks to this process. This simple guide will assist you in figuring out how much corrugated board you’ll need for your roof.

Measuring your roof’s dimensions is the first step. To begin, measure the width and length of each section of the roof where the corrugated metal sheets are going to be installed. If the shape of your roof is complicated, divide it into easier shapes like squares or rectangles. This will greatly simplify the area calculation.

After obtaining the measurements, multiply the length by the width of each section to determine its total area. One section of your roof, for example, would measure 20 feet long by 10 feet wide, or 200 square feet (20 x 10 = 200). For every area of your roof, perform this computation once more.

Next, take your roof’s pitch or slope into consideration. The majority of roofs are slightly angled to aid in water runoff. If possible, measure the pitch angle or make a visual estimate. Pitch is important for precise measurements because it determines how the corrugated sheets fit and overlap.

Now think about the area that each corrugated metal sheet covers. Manufacturers usually specify the area that one sheet is intended to cover. A typical corrugated metal sheet, for instance, might be 32 square feet in size. To find the number of sheets you’ll need, divide this number by the total area of each roof section.

In order to account for waste or cutting adjustments, add a buffer to your calculations at the end. In order to make sure you have enough material to cover overlaps, corners, and any measurement errors, it is advisable to add an additional 10% to 15%. This buffer guarantees that supplies won’t run out in the middle of the project.

You can determine with confidence how much corrugated board you’ll need for your roof by following these steps: measure precisely, take the pitch into account, calculate coverage per sheet, and add a buffer. This planning guarantees a more seamless installation process and aids in cost containment.

What technical characteristics should be taken into account during calculations

Prices for corrugated board

Corrugated board

The following profiled sheet indicators are affected by the methods of calculation.

    Thickness. Currently, there are three types of sheets in the implementation: wall, roofing and universal. Standards prescribe that the thinnest steel can be used for the wall, the roofing profile has the thickest. Universal is located in the middle. But this classification is very conditional, unscrupulous manufacturers are trying to deceive consumers, make products from thin steel. It is impossible to check the thickness of the sheet without laboratory equipment, the metal is covered with several layers of other materials. During calculations it is better to insure, increase the length of the ceiling and reduce the step of the crate.

When selecting a material, the corrugated board’s thickness is a crucial factor.

The corrugated board wave’s dimensions

More intricate roofs result in a higher proportion of corrugated board waste.

"There are easy steps to follow when calculating corrugated roofing sheets for your roof to make sure you have the correct quantity of material for the job. You can calculate the number of sheets required without wasting material by taking precise measurements of the roof’s dimensions and taking overlaps into consideration. This guide helps homeowners and do-it-yourself enthusiasts alike confidently plan and carry out their roofing projects by breaking the process down into simple, doable steps."

How to use a calculator

Using a specialized calculator is the quickest and most straightforward method of calculating the corrugated board on the roof. Prior to beginning construction, you must choose the kind and specifications for the roof and sheet. The following source data will be needed for the calculator:

  • the size of the sheet is not the total, but only effective (working);
  • linear dimensions of rectangular slopes and their number;
  • linear dimensions of triangular slopes (vald) and their number;
  • the sizes of trapezoidal slopes and their number.

To compute, you must be aware of the roof’s precise measurements.

The calculator can calculate and summarize the areas of each geometric figure thanks to a straightforward program. Such computations are rarely used by experienced roofers. Too many unanticipated factors affect the final calculations, so no computer program can account for every possible roof configuration.

This kind of calculator should only be used to get indicative values and then only with extreme caution. He ignores the length of the sheets, which has an impact on the number of joints in each joint. The width of the overlap and t width are impacted by the slopes’ angle of slope, which is a parameter that the calculator ignores. D.

Approximate values from the calculator

A practical example of calculating roofing material

The number of profiled sheets can be determined by applying trigonometric formulas. However, not all aging builders are able to recall what COS or arctg is, where to find them, or what to do after they’ve been found. We provide the most straightforward computation method; all you need to know is the material covered in first-class arithmetic lessons.

Consider the gable roof, which is the most common and basic type.

The amount of corrugated board and metal tiles can be calculated in the same way; roofing materials have the same styling technologies, extra elements, and fixation techniques, as well as the same performance characteristics. There are minor variations in the price and appearance, but the computation process is unaffected by these factors. To help with comprehension, the instructions include the roof’s size. They also specify that the rafter system and specific metal tile parameters must be used in their computations.

Step 1. Find out the size of the sheets. The manufacturer indicates the general and working width of the sheets. The working width takes into account the size of the waves of waves during installation. In our case, the total width is 119 cm, and the working 110 cm. A wider wave will always lie on top, due to this, the tightness of the fit. The upper wave completely closes the lower one – the probability of entering the subcutaneous space of snow or rain is excluded. The corrugated board has no waves, it has only parallels located at the same height of the crest, which slightly simplifies the calculation process, there is no need to consider this parameter during the choice of the ridge element and wind planes. For a profiled sheet, you can buy strips with lower sides of the sidewalls, they close a small light between the roof and the crate.

Step 2: Determine the rafter system’s dimensions. In our instance, there are 11 m 67 cm between two extreme rafter legs and 10 m 60 cm between the building’s walls. Given the size of the house, the rafter system needs to be designed in compliance with all regulations and provide the required rigidity and carrying capacity.

Important. In order to reduce the number of unproductive waste of corrugated board and facilitate roofing work, it is recommended to fit the size of the crate to the size of the profiled sheet. This will not only exclude the need to fit sheets, but also improve the appearance of the roof. It will be symmetrical, the screws will be located on equal removal. Another problem of circumcised sheets – cut metal in the sites quickly oxidizes. The sizes of rust are not critical, the metal does not spoil very quickly. The problem is that rust with water is washed off to coating the roof and forms ugly red heights. It is impossible to remove them, the oxides of the iron are tightly eaten into the surface of the coating.

Step 3. Calculate the number of sheets of metal profile. In our case, for the roof you will need 11 pcs. × 110 cm + 90 cm = 12 m 19 cm. During the calculations, it was meant that 11 sheets with a working width of 90 cm are not enough, in connection with this it is necessary to increase the coating by 9 cm and due to this to achieve the size of the roof on the skate of 12 m 19 cm. In this case, the overhang on the skate will be 12 m 19 cm – 10 m 60 cm = 159 cm/ 2 = 79 cm. If such a distance seems large, then it can be reduced to acceptable parameters with a multiple of the width of the wave of roofing material. As a result, after choosing the optimal option, the length of the roof cen was 12 m 1 cm. Taking into account the size of the sheets, the crate for the roof should have dimensions of 12 m 1 cm along the ridge and 7 m 97.5 cm according to the slope of the ramp.

Estimating the roof’s dimensions

Step 4: Measure the skate’s length and move it to the opposite lower roof side (cornice) to remove 7 m, or 97.5 cm. Make sure the corners are perfectly rectangular by carefully inspecting them. All subsequent rows will be steps if the first row is uneven. It is extremely difficult to straighten the sheets by slightly shifting the ceiling profiles, and manufacturers do not advise doing so at all. There will be multiple issues if they aren’t in sync.

  1. The cracks in the places of overflow of sheets are increased, the risks of blowing snow or rain will appear. To eliminate the problem, it is necessary to increase the length of the overlap, and this changes all calculations, increases the consumption of expensive roofing materials.
  2. In places of bending, the sheets touch each other not on the plane of the surface, but along the line. This position causes significant loads along the lines, the thickness of the profiled sheets is not designed for them. As a result – the coating can bend in these areas, protective layers are damaged, oxidative processes are accelerated. In the future, leaks requiring the repair of the roof appear at such points.

Measuring the rectangle’s diagonals is necessary to verify that the crate’s corner is correct. If there is a difference, the skate should always be stable and only the cornice section of the crate can be moved in either direction.

The precise slope sizes

Sensible guidance. You must speak with a manufacturer representative prior to placing an order. Coordinating the length of the sheets is necessary; however, depending on production capabilities and delivery challenges, it may need to be adjusted in some instances. When purchasing a finished metal profile in standard sizes, you must consider how the overlap will vary based on the slopes’ angles of descent.

Step 5: Compute the extra components. They must be ordered in tandem with the roof purchase. The majority of producers create components in standard lengths of one and two meters. The installation of a gable roof will require these extra components.

Bar of cornices (dropper)

On this, the roof’s preliminary calculations are complete. The value of the roof can be calculated by multiplying the number of elements by their respective prices. However, not everything is that easy. Why? You must factor in the entire construction estimate and perform the most thorough computation possible because the cost of the roof includes more than just the coating.

Volume calculations for ordering

To calculate the amount of corrugated board needed for your roof: 1. Measure the length and width of your roof in meters.
2. Multiply the length by the width to get the area of the roof in square meters. 3. Check the size of the corrugated boards available and calculate how many you need to cover the roof.
4. Consider buying a little extra to account for cutting and any mistakes. 5. Add about 10% to your total for overlapping and trimming.

Every roofing project needs to account for the quantity of corrugated board that will be required for the roof. It guarantees you purchase the appropriate quantity of materials and prevents unforeseen expenses or shortages. Measure the width and length of each roof section where the corrugated board is going to be installed first. Accurate measurement of these parameters is necessary to guarantee accurate computations.

Next, multiply the length by the width to find the area of each roof section. For instance, 200 square feet would be the area of one section of your roof that is 20 feet long and 10 feet wide (20 x 10 = 200). For every area of your roof that will have corrugated board covering, repeat this process.

Once the area for each section has been determined, add the total area of the roof that needs to be covered. The amount of corrugated board you need to buy will depend on this total. A small amount (usually about 10%) should be added to account for waste from cutting and installation.

Since corrugated boards are typically sold in standard sizes, make sure to measure the boards that are available and determine how many you’ll need based on the size of your entire roof. You might need fewer boards if the ones you choose are larger than the area you calculated, but you’ll still need to trim them to fit your roof precisely.

Finally, think about your roof’s pitch and configuration. You might have to modify your calculations if your roof has a complicated shape or a lot of angles. To guarantee a seamless and effective roofing project, confirm all measurements and computations one last time before buying supplies.

Video on the topic

Professor for the Walm. Without waste. 170m kV in 1 day. New Technology.

How to calculate the corrugated board

How to calculate a gable roof

What do you think, which element is the most important for a reliable and durable roof?
Share to friends
Alexandra Fedorova

Journalist, author of articles on construction and repair. I will help you understand the complex issues related to the choice and installation of the roof.

Rate author
Innfes.com
Add a comment