It can be difficult to remove a skirting board from the floor, particularly if you don’t want to damage the board in the process. Regardless of the material—wood or plastic—careful handling is necessary during the process to prevent splintering or breaking the material.
To begin with, carefully place a chisel or a flat pry bar between the wooden skirting board and the wall. Use a little block of wood to shield the wall from the edge of the pry bar. Ease the skirting board away from the wall inch by inch as you move slowly along its length. Evenly apply pressure to avoid splitting the wood. If the skirting board is nailed in place, carefully pry each nail out with a hammer being careful not to pull the board too hard.
Although they can be removed more easily than wooden ones, plastic skirting boards still need to be removed carefully. Find the joints where the boards join to start. Plastic skirting boards are frequently fastened in place with clips or snaps. To carefully remove these clips, use a pry tool or a flathead screwdriver. Proceed carefully along the board, releasing each clip individually. To stop the plastic from breaking or cracking, don’t apply too much force.
Once the skirting board is loose, carefully lift it off the floor, regardless of the material. Examine the wall and the floor to make sure that removal did not cause any damage. Use a scraper and a mild adhesive remover to clean the area if there are any lingering spots or adhesive residue, being careful not to gouge or scrape the surface.
| Method | Description |
| Wooden Skirting Board | To remove a wooden skirting board, start by gently inserting a flat pry bar between the board and the wall. Slowly pry it away, using a putty knife to loosen any adhesive. Take care not to break the board or damage the wall. |
| Plastic Skirting Board | For plastic skirting boards, begin by wedging a thin putty knife or a plastic pry tool behind the board. Slowly work around the board, applying gentle pressure to release it from the adhesive or clips. Avoid bending or snapping the plastic during removal. |
- Types of floor skirting boards
- Ways to attach skirting boards
- Basic dismantling rules
- How to remove wooden skirting boat from the floor?
- Removing a skirting board fastened with self -tapping screws
- Dismantling of a wooden skirting board with chopic
- Removing a plinth from MDF
- Video on the topic
- How to remove an old baseboard. Dismantling of wooden skirting boards
- How to quickly remove a plastic skirting board from the wall and floor
- Dismantling of the skirting board Cubu Flex Life.
- How to remove old plinths
- Dismantling of plastic skirting boards / how to remove plastic skirting boards / DISMANTLING A PLASTIC BASEBOARD
Types of floor skirting boards
The following problems are resolved when floor and wall joints are arranged using skirting boards:
- Allows you to hide the gap formed between the wall and the floor when installing a parquet board, laminate or other types of flooring.
- Hides surface defects in walls that appear during installation work.
- Performing the function of the cable channel for laying inside electrical communications and other cables.
- Harmonious docking of walls and floor with each other.
The following kinds of skirting boards are the most widely used among the many varieties that are available:
- Wooden. The standard option, for the manufacture of which oak, bean or coniferous wood is used. Outwardly, such a plinth looks very beautiful, and in addition it is also environmentally friendly. However, wooden products are quite expensive, and also complex in installation. They must be accurately adjusted to the parameters of the room, and then finish.
- Plastic. Are in demand due to presentable design and affordable cost. Also, plastic does not require complicated care, and also usually has a cable channels to accommodate communications. Such designs do not require varnish or paint treatment. For the manufacture of plastic structures, PVC is used. The key minus is the vulnerability to damage at a significant load, as well as the need to use plugs and connectors during installation.
- Veneered. It is made on the basis of wood with a presentable surface. Has a wide color scheme, natural texture and affordable price.
- Aluminum. It is usually found in commercial premises, but in residential buildings it is also appropriate.
- Polyurethane. Characterized by convenience in installation, but requires finish staining.
Ways to attach skirting boards
Its fastening and the kind of skirting boards can be done in a variety of ways and with modifications.
Among them are:
- self -tapping screws (any kind);
- veneered or wooden nails;
- any types of adhesive mixtures;
- special mounting mounts;
- Wooden chopic.
Basic dismantling rules
Without auxiliary devices, removing the old skirting board will not be feasible, so it is wise to have a set of these tools ready in advance.
Considering the skirting board’s specifications, the following instruments might be useful:
- nail or scrap;
- screwdriver or screwdriver;
- putty knife;
- Shovel or kiyanka.
Crucial! so that it is preferable to use an extra pair of clothes and shoes when carrying out disassembly procedures. Even though there isn’t any dust or trash when skirting boards are removed, they are still there.
If the old skirting board was fixed with self-tapping screws, then a screwdriver or screwdrivers will suffice to finish the job.
You must first remove all electrical and other wiring from any cable channels that may be present in the skirting board. There is a chance of receiving an electric shock if this is not done.
How to remove wooden skirting boat from the floor?
Sometimes the skirting board needs to be disassembled in order to be replaced or to apply a new coating. Since the superfluous design can be disposed of, there are no unique regulations or limitations in the first scenario. However, you will need to exercise caution if the skirting board is going to be used again.
In order to remove wooden skirting boards that were collected a few decades ago, you must first assess how they were attached. Their hats will be visible on the surface, speaking above it, or slightly drowned if this was done with nails. Fomka can be used to extract these fasteners.
You must locate the fixation sites at random if they are plunged. The skirting board that is fastened to the wall rather than the floor is the hardest to remove. After all, wallpaper or plaster can be easily damaged in such circumstances.
Removing a skirting board fastened with self -tapping screws
If the fixation was done with self-tapping screws, all you have to do is locate their hats. They are either submerged in the body, as in the last instance, or they are visible above the waterline.
Fasteners need to be unscrewed with a screwdriver or screwdriver in order to be extracted.
Dismantling of a wooden skirting board with chopic
Structures that are fastened to the ground by tiny chokes are less common. There is a 5% chance of finding such a fixation technique. Usually, it was utilized during the installation of pricey structures made of opulent wood species to preserve the product’s aesthetic appeal.
The fastenings in this instance are subtle, round knots that resemble wood grain. They can be located by their dark rim or by a material pattern.
Removing a plinth from MDF
Products that are gathered from MDF are fastened to the latch using specialty fasteners. After being separately screwed to the wall, they are planted.
Similar designs require the application of a wide spatula that is driven under the lower portion like a lever in order to be disassembled. After that, the baseboard should be raised carefully.
Whether a skirting board is made of plastic or wood, it must be removed from the floor carefully to prevent damage. Prepare the space surrounding the skirting board first. This entails getting rid of any obstructions and making sure you have the necessary equipment on hand, like a utility knife, hammer, and pry bar.
To start with, use a utility knife to score the paint or caulking along the top edge of the wooden skirting boards. When you remove the board, this helps keep the paint from pealing off the wall. Next, beginning at one end, carefully slide the pry bar between the skirting board and the wall. Press the board gently to remove it from the wall. Apply pressure and move the pry bar along the length of the skirting board until it comes off completely.
Removing plastic skirting boards without causing damage can be more difficult. Start by scoring any caulking or adhesive along the top edge, just like you would with wooden boards. Gently pry the board off the wall with a putty knife or flat pry tool. Because plastic boards are more likely to shatter or snap, exercise caution when using excessive force. Continue working slowly and steadily along the board’s length until it comes completely off.
Examine the skirting board for any damage after it has been removed. If you intend to reinstall it, mark every component and keep it in a secure location to prevent damage or loss. To get ready for reinstallation, clean the wall and the back of the skirting board of any remaining caulking or adhesive.
Whether the skirting board is made of plastic or wood, you can remove it from the floor without doing much damage if you follow these careful instructions. To ensure that the board stays intact for use or replacement in the future, keep in mind to work carefully and methodically.
We look at doable ways to safely remove skirting boards without causing damage in our guide, "How to Remove Skirting Boards: Wood and Plastic." Whether you’re working with plastic or wooden skirting, our detailed instructions focus on gentle methods that protect the boards and guarantee a seamless removal. You can successfully update your space without worrying about damaging your skirting boards if you adhere to these simple methods."
