Yandy roof what it is

The Yandy roof, also known as a butterfly roof, is a distinctive architectural style that has grown in popularity due to its practicality and distinctive design. In contrast to conventional roofs that have multiple sloping directions, a Yandy roof rises from opposing sides and unites at a central peak. This forms an inverse W- or V-shape that resembles a butterfly’s wings in flight. In addition to giving buildings a contemporary aesthetic, this striking appearance has functional uses.

Because of the Yandy roof’s angled slopes that facilitate easy precipitation runoff towards the central valley, rainwater drainage is made possible. This feature reduces the possibility of water collecting and possible leaks, which is especially helpful in areas that receive a lot of snowfall or rain. Larger windows or clerestory openings along the central ridge can also be accommodated by the steep slopes of the Yandy roof, which will improve natural light penetration and offer expansive views of the surroundings.

The Yandy roof gained popularity in the mid-20th century, especially in modernist and contemporary architecture, and has seen a resurgence recently because of its environmental benefits. Depending on the climate and building orientation, the sharp angles and smaller surface area compared to conventional flat or pitched roofs can help improve energy efficiency by reducing heat gain and loss.

What is the yendova of the roof

One of the primary components of the roofing area is endova. To put it another way, Endov is a roofing component that resembles an inner angle. It is situated where two roofing slopes converge.

The quick removal of atmospheric precipitation from the roof space is the primary duty of Endova. It is able to remove water and put a significant load on the entire roof system thanks to a unique Endova device. Therefore, an Endov is the location that is most sensitive to moisture.

It is especially crucial to perform dependable sealing and careful installation under these circumstances. Ultimately, moisture from the roof will fall onto the Endov.

A word of advice: galvanized steel is the best material for the equipment. Its characteristics will greatly increase the lifespan of the roofing system as a whole as well as the yendov.

The yendovs are typically made out of metal sheets.

Based on the characteristics of the design, one can differentiate:

  • the bar of the lower yendova;
  • The bar of the Upper Endov.

At the joints of negative angles, the bottom is installed. This component’s function is to keep the area beneath the roof dry.

Installing a bar of this kind is a good idea even prior to installing metal tiles or corrugated board for roofing.

The purpose of the upper upper is decorative. Such a bar gives the joints between the two slopes a polished appearance. Put differently, Endova determines how your roof will look in the end.

In contrast to the lower, the upper yendova’s bar needs to be fixed after the metal or corrugated board is installed.

Advice: It’s important to pick the endova’s attaching location very carefully. This will not include harm to the lower valleys’ central region. The best self-tapping screws for the roof are ideal for fastening. It is advised to fix the layers of lining to prevent potential leaks in the installation joints.

The way roofing slopes are connected, connected, connected, and entwined is the constructive difference.

Installation Endov: Features

The installation of a crate is the first step. At the same time, it’s critical to keep in mind that the joints in both roofing slopes should have a continuous structure. Possessing a crate with reinforcement on both sides is crucial.

Over a wooden groove, a waterproofing layer is applied. Remember that it keeps moisture out of the area beneath the roof.

When horizontal joints are present on the roof’s yndov, there is a greater than 100 mm overlap. Experts advise adding an extra waterproofing layer to a roof with a flat slope angle.

Ignoring the installation of a second waterproofing layer is not advised. If not, Endov may collapse very quickly. In addition to its repair, the cost of funds will be required for the roofing system’s restoration as a whole.

Important: Use a specific seal when using metal tiles for roofing. It tends to grow on its own.

Recall that the arrangement is necessary for any roof that has a complicated constructive solution. As a result, it is crucial that you adhere to all installation guidelines for this component.

The standard states that it is best to use both closed and entwined yendovs at the same time when equipping roofs with a steep slope. Simultaneously, the decision is contingent upon the roofing system you have installed on your residence.

Remember that the closed and entwined yendov’s unique feature is the arrangement of a waterproofing layer. Considering that high-quality material is fairly expensive, this is a rather expensive event.

There is no need to add another waterproofing layer when using the open-open plan. You are welcome to examine the open yendova’s design in more detail. Precipitation does not accumulate on the element by itself. Conversely, they dissipate rapidly.

Advice: Installing a waterproofing system using standard technology is part of Open Endov. It is typically applied when dealing with pitched roofs.

Expert advice: Initially, the roof’s first row of roofing material needs to be installed, reaching the yendova’s lower end. Once this work is finished, you can begin repairing the waterproof layer.

There are a lot of building sites nowadays. Not only can you view all of the work there with clarity, but you can also receive expert advice. Sites frequently have images and videos of roofing work.

Installation of yendovs on Ondulin’s roof: Watch the video for instructions.

Most people conclude that the professionals’ organizational structure should be trusted. Therefore, it is advised to invite experienced individuals to complete installation work on the roof. This will eliminate all risk, especially financial risk.

We now know what the roof is. The most intricate structural components can be equipped independently if you adhere to every instruction.

How to make an yendov on the roof

The roof is becoming more and more useful beyond its practical use. It is frequently this feature, the building’s focal point. These kinds of roofs are made up of numerous planes joined at various angles. A portion of the connections have positive angles and are shaped like ridges, while the remaining connections have negative angles and are shaped like yends. A properly made roof is necessary to ensure that the attic is always dry.

Fundamentally, a Yandy roof is a revolutionary approach to roofing solutions that combines state-of-the-art technology with sustainable design ideas. Yandy roofs are designed to seamlessly integrate solar panels into their structure, allowing them to harness renewable energy sources and offer long-lasting protection, in contrast to traditional roofs, which are primarily used as weather barriers. Through energy generation and efficiency, this creative design not only lowers carbon footprints but also provides long-term cost savings. Yandy roofs show how cutting-edge engineering can successfully address environmental needs by fusing practicality with environmental awareness, paving the way for a more environmentally friendly future in building."

End roofs

Sharp corners are formed on the roofs of complex shapes where auditory windows protrude. They can be found at the intersections of two slopes. The roofs are referred to as the apple, and the conjugation place is called Endov.

What is Endova?

Complexly shaped roofs are a great way to decorate a building and look very beautiful, but creating the devices and designs for them is difficult. These parts of the roof bear a heavy load because of their design elements because there is always a lot of snow and water. As a result, the crate is improved, and serious waterproofing measures are taken compared to the surface.

Features of the rafter systems

Depending on the roof’s shape, the rafters from various slopes in Endov can be connected at various angles. The rafters are attached from the slopes to the rafter leg, which is installed at the junction. When the joint is small (up to 2 m), it can be secured with two nails on each side; however, when the joint is long, a metal lining strengthens the connection.

The yendova’s rafter leg is appropriate where the largest load is located, or in the widest spot.

The backup is positioned as far below as possible.

The reinforced crate at the intersection of the two roof slopes is equipped with a device that varies depending on the kind of roofing material:

  • Intermediate planks are installed under the metal tile in Endov – in the middle between the main. That is, in this place the step is half as much. The length of the additional strips should be larger.

  • Under the profile, slate, ceramic tiles, longitudinal boards are nailed – along the whole joint. The width of the boards-at least 100 mm, are nailed closely two or three on each side. The width depends on the size of the selected substrate. Under the profile, slate and ceramic tiles need two or three boards on each side
  • Under Ondulin, two boards are needed at least 100 mm wide. But in this case, they should be located at a distance of 15 cm from one another. A gutter is laid in the formed opening. Under the Ondulin between the two boards there should be a gap of 15 cm
  • When installing a soft roof, a crate on the slopes is solid, so there are no features.
  • Although we have provided standard sizes and requirements, certain manufacturers may have unique demands. You will receive installation instructions along with information on crate requirements and other technical details when you purchase roofing material. It is evident that following their advice is essential.

    Endova device

    Since every roofing material has unique properties, discussing the device as a whole is pointless. Consider the most well-liked ones independently as a result.

    On a roof of metal

    As previously stated, the crate is made twice as frequently at the location of the ripe slopes, under a metal tile. This crate holds the lower Endova bar, which is a galvanized sheet with sides that are folded along the edges and a fold line in the middle. This component alludes to the inputs, which are complementary to the primary content. Two-meter pieces are used.

    Jack of Metal

    Below is where the Endov plank installation starts. The element’s edge begins slightly behind the roof’s ovation and is cut 20 to 30 mm below the overhang. Sewing (sip) is formed from this "remainder." Please take note that the apple bar should finish above any drain groove and behind any overhang. Water will flow into the roof if it is shorter than the overhang.

    The joint is sealed with a sealant (you can use bitumen mastic to smear the entire overlap) before the next sheet is placed on top, with a 20–30 cm vision. Add as many sheets as needed, cut them, and secure them close to the skate.

    The apple sheet can be secured in two different ways.

    • special self -tapping screws closer to the edge;
    • Klyaimers for the side.

    From corrugated board and slate

    Several boards are laid under these materials in Endov. A waterproofing strip is fixed on them, which is then connected to the waterproofing membrane fixed on the slopes. The overlap should be at least 10-15 cm, the joints are connected using bilateral tape. Further, the installation is similar to the above: the lower yendny bar is also laid, to which the universal seal is glued, then the roofing material is mounted. The device of yendova on the roof of corrugated board in this case can be supplemented with sealing tape with sealant. The sealant strip is applied on both sides from the place of bending the roof. After the installation of roofing material in the protrusions of the wave, a large free space remains. Water, snow, garbage can get there. So that this does not happen, the gap is filled with sealant, applying it in layers. In the case of a profiled sheet, there are several options for designing yendova:

    • Open. This is when the sheets of corrugated board are cut off at a distance of 60-100 mm from the bend line. In this case, the bar and slices are visible. To close this "farm", a decorative gutter is laid on top of the roofing material that closes the cut line. He is attached to the crate with nails.

  • Closed. The corrugated board is cut strictly along the middle of the middle of the yendova, joins almost without a gap. No additional elements requires.
  • Intertwined. A difficult method for independent installation. Endova"s space is overlapped by sheets of material that enter the other side alternately. This method with hard coatings is practically not used, since it is more suitable for a soft roof.
  • Regardless of whether you select an open or closed slope connection, the pie’s overall device stays the same. The corporate stratum cutting technique remains unchanged.

    The roof’s tile structure is precisely the same as when using a profiled sheet. The distinction lies in the fact that the continuous crate needs to be wider—at least 35 cm on each side of the joint. Endov features have a tile mount; some pieces are so severely broken that a regular lock cannot be used to secure them. Next, a soft, acid-resistant wire is inserted into the hole that has been drilled in the upper portion of the tiles. To fix the tile in the desired position, drive a nail into the crate and wrap the wire around it.

    The tile-equipped appliance in its second iteration.

    When it comes to ondulin, the crate beneath the yndova is made up of two boards that are symmetrically positioned 15 cm apart from the center rather than a single piece. Between them, a special gutter is installed.

    A distinct indent is made in between the packed planks.

    Installing starts below; proceed upward. After the shape is adjusted, the apple gutter’s first leaf is placed on the roofing material’s edge. Attached to the crate using nails from the top. The following sheet is laid with at least a 15 cm overlap.

    The gutter’s upper fragment obstructs the bottom by at least 15 centimeters.

    Roofing sheets are installed once the gutter is completely installed. Cut first, leaving a margin; the mark is positioned 5–6 cm beyond what is required. Cut off (jigsaw or grinder) along the marked line. Once installed, use the gutter protrusion to precisely mark the cut line. After being cut off a second time, replace. The Ondulin sheet weighs a little, so performing all the operations is simple.

    Ondulin was cut twice, first roughly and then definitely.

    Special roofing nails are used to secure the laid sheet, and a toned hat is included. It must be fixed in each wave by pulling back from the center line as much as is practical.

    Anchored with unique nails

    The yendov installation on Ondulin’s roof is presented in video format.

    Tin roofs

    Although uncommon, this kind of roofing material is used occasionally in the construction of private homes. The roof of tin’s jend is manually attached with the aid of a kiyanka and a specialized tool.

    What is Endova and what is her device

    A typical roof with two gentle slopes won’t surprise anyone these days. A lot of developers opt for home projects with intricate roofs because they want something more fundamental. For instance, the tent and the Valmova both have stunning appearances. But the roof’s complicated shape necessitates the addition of other components. We’ll talk about one of them today, Endov, and its significance for those who are only beginning to comprehend how a house’s roof is put together.

    What is Endov and her purpose

    Thus, Endova serves as a connecting piece at the point where a complex roof breaks into two planes. It is situated where roofing slopes join to form a negative angle, in contrast to the skate.

    The areas serve the straightforward function of keeping water and other waste from getting inside the roof.

    In actuality, they act as a sort of groove, assisting in clearing the roof of everything. The number of joints on the roof increases with its complexity of configuration. Thus, more of these protective gutters will be required.

    There is a broad range of roofs that need to have these components mounted. Values are typically placed on the cross-shaped roofs and on the letters "g" or "t" that are formed like letters. most common type of roofs, a T. It is important to keep in mind that the roof may have bends near the auditory or attic windows that protrude. By the way, bear in mind that the cost of work will be significantly impacted by the complexity of the roofing structure. Furthermore, maintaining a complicated roof in the future won’t be inexpensive.

    It is best to create a thorough plan with all of the roof’s adjacencies noted in order to ensure that nothing is missed. Next, this plan is split into distinct square and rectangular sections. The house’s largest rectangle represents the structure itself, and smaller squares and rectangles denote the extensions. After indicating the ruins, join the house’s roof’s corners with the extensions’ roof angles. Thus, the locations of our future gutters are decided upon in advance.

    Important: You may overpay for the yendova device if you have the wrong idea about it. Furthermore, the result could be not just streams of water from the ceiling but also a collapsed roof. This is conceivable if a significant amount of snow accumulates on the roof instead of melting it. As a result, it is worthwhile to speak with experts who will consider sedimentary and wind loads. Everyone has heard the story of the stingy guy who paid twice, after all.

    A particular type of roof building known as a "yandy roof" has grown in popularity due to its distinctive fusion of style and functionality. In contrast to conventional roofs, which have a predetermined slope or design, whimsical roofs are distinguished by their unusual angles and forms. These roofs have a dynamic and striking appearance because they frequently have multiple facets and irregular surfaces.

    One of the main characteristics of trendy roofs is their ability to blend in perfectly with contemporary architectural designs, giving building designers and homeowners alike a means to showcase their uniqueness and inventiveness. Wendy roofs can change a building’s visual impact and make it stand out in its surroundings by departing from the conventional gable or hip roof forms.

    Sunny roofs are not only aesthetically pleasing, but they also have functional uses. Their distinctive shapes can maximize ventilation and natural light intake, improving a building’s interior comfort and possibly saving energy expenditures. Because of the design’s adaptability, features like rooftop gardens, dormers, and skylights can be added to improve the usability and livability of the area below.

    Video on the topic

    How one can cut off the rafters on the yendov!

    What is Endova? "The heading is?!"

    roof with three pediments, yendov

    End roof

    Endov roof

    What do you think, which element is the most important for a reliable and durable roof?
    Share to friends
    Alexandra Fedorova

    Journalist, author of articles on construction and repair. I will help you understand the complex issues related to the choice and installation of the roof.

    Rate author
    Add a comment